For a full-length mirror order, the sample, factory check and report need to describe the same build. You can approve the appearance and still have unanswered questions about the hanger or packing. We inspect during production, inspect 100% of units before packing, and carry out final inspection. We also have seven named test capabilities. Our general quality-control description does not assign every test to every model or publish pass limits. The order specification has to define that scope.
Inspection Starts with the Approved Mirror
Start with how your customer will use the mirror. Is it going on the wall or standing on its own support? Does it have lighting? Those answers determine whether the order needs attention to hanging hardware, a floor stand or an electrical version. Put the model and revision on the approved sample, order specification and inspection record. One identifier should connect them.
When specifying a large mirror for wall for your range, separate what you see from what the drawing needs to show. Size and finish are visible. Backing, hanging orientation and hardware need their own description, as does the packed configuration. Add the visible glass dimensions where your approval depends on them. Our published materials do not set these details for a particular buyer’s order.
When a finish or hanger changes, update the sample or drawing revision too. Otherwise production may be checked against yesterday’s specification while the shipment is expected to match today’s.
Where Inspection Happens in Production
We describe inspection at three stages. Work is checked in production; every unit is inspected before packing; final inspection is a further checkpoint. Our description does not specify defect classes or locate the final check relative to carton closure. The order record can close that gap by naming each hand-off.
What is the production check being judged against? Your drawing can supply a dimension, while the approved sample supplies the finish reference. A specified part also gives the inspector a fit to compare. Record the feature and what happened to a unit that missed the agreed limit. Your team can then read the finding against the same reference we use.
Agree the coverage of the pre-packing inspection as well. If you expect accessories to be checked alongside the mirror face, edges, finish, hardware and label, put that in the order requirements. Then state where final inspection occurs and which record closes the order. Writing “final inspection” on an order leaves those decisions open.
Match Each Test to the Mirror’s Construction
Our available tests cover salt spray and adhesive firmness as well as suspension, load bearing, drops, stability and light-box operation. We can prepare mirror reports to buyer requirements. Those are available methods; the record does not say that all seven belong on every mirror’s test plan. Ask what question the test is supposed to answer before adding it to the order.
A suspension or load-bearing result needs the identity of the hanger and fixture. Ask how much load was applied, for how long, and what would count as a failure. A bare “pass” leaves you unable to check those conditions against your order.
If your order includes an easel or floor stand, specify that support in the stability test request. A different stand changes the test setup and what the result means.
A salt-spray report should name the metal part and exposure condition. If it covers one hanger, it says nothing about a different frame finish unless that finish was tested too.
An adhesive-firmness request needs to identify the joint under examination. “Drop tested” needs clarification too: was the mirror inside its shipping carton, or was it unpacked? Your shipping-protection question calls for the packed setup.
On a lighted mirror, identify the electrical version and operation checked. Do not attach a light-box result to an unlit model.
Keep one test record beside the order specification. A later reviewer should be able to identify the sample, setup, limit and result without guessing what ‘passed’ meant.
Make the Inspection Record Traceable
A useful mirror report identifies the SKU and approved revision, production lot, date, inspection coverage or sample size, method, acceptance limit, result, deviations and disposition. Our published information says mirror reports can be prepared to buyer requirements. Send the required report fields with your inspection request so we can establish the reporting scope.
Attach the model reference to the report. For a wood frame mirror, include the approved finish and the support configuration in that reference. Changing either can change which checks are relevant.
Which packing was used? Save that reference beside the product revision. A product inspection looks at the mirror; a shipment test may look at its carton and protection. Identify the carton revision, corner protection and orientation used for the test.
What Buyers Should Confirm Before Release
Before production, approve the sample or drawing and its measurable requirements. At release, match the report to that revision and the production lot. A mismatch is a hold point; resolve which version was checked before the cartons move.
When choosing from our oversized mirror wall range, settle the individual model before requesting release evidence. A range name cannot identify the construction being inspected.
Destination requirements are a separate input. Your team identifies the market or customer rule; then compare its named test and limit with the report. Having a test available does not tell you whether its method and limit satisfy that rule.
Before the Cartons Leave
At release, you should be able to open the order file and see which mirror was approved and what was checked on the lot being shipped. Our published record names the checkpoints and available tests; the order specification defines which ones apply. That is the file your team needs when reviewing a shipment.
Frequently Asked Questions
Does Kingwin inspect every full-length mirror before packing?
Yes. We describe a 100% inspection before packing. That tells you how many units are inspected, but the order still needs an agreed checklist. Include accessories explicitly if you need those checked too.
Which tests are available for full-length mirrors?
We have capabilities for salt spray, adhesive firmness, suspension and load bearing, plus drop, stability and light-box operation. Your mirror may need only some of these. Confirm the applicable setup and acceptance requirement with the request.
Can a supplier test report cover a different mirror model?
Do not assume it does. A report for another model needs a documented explanation of why its results apply to your ordered construction. Without that explanation, request evidence for your model and revision.
What should a buyer request in an inspection report?
Start with identification: which SKU, revision and lot were checked, and on what date? Then request the coverage, test method, acceptance limit and finding. Ask for deviations and their disposition too; a result without that context can leave an order question unresolved.
Does a factory test capability prove compliance in the destination market?
No. A factory capability list is neither a market certificate nor a test result for your mirror. Compare the destination rule with evidence for the exact configuration you ordered.
